Models SF-5 and SW-5 produce up to 5 lbs./hr. of water mist and come with (SF-5) and without (SW-5) inlet air filters. Air filters
are recommended where industrial dust is present in the air. Three dispensing domes are available
providing 360 degree, two-way or one-way directional discharge of water mist.
Typical applications are photo and test laboratories, produce storage areas and stock rooms. Specifications (748 KB). Installation Sheets (348 KB).
The Model SW-2 will produce up to 2 lbs./hr. of water
mist. Water mist is created by centrifugal force from a simple high speed rotating disk and
an internal fan dispensing a stream of fine moisture particles which travels only a few feet
before emistating completely into the surrounding atmosphere. The rotating disk is carefully
balanced to insure quiet and dependable operation over its long life. The directional dome may
be rotated to any position for convenience of installation.
This unit is ideal for small, well-enclosed room like tobacco humidors or larger rooms where small amounts of humidification would be beneficial. Specifications (530 KB). Installation Sheets (337 KB).
The Humidity Source Model SF-10 or SW-10 is capable of
producing up to 10 lbs./hr. of water mist. Three dispensing domes are available providing 360
degree, two way, or one way directional discharge of water mist particles. With the addition
of the Humidity Source heavy duty primary air intake filter (not shown) the Model SF-10 is especially
recommended for applications in which the air is laden with industrial dust.
Typical applications include large test laboratories, warehouse storage areas, printing plants, large humidors and produce storage buildings that require controlled humidity conditions. Specifications (139 KB). Installation Sheets (360 KB).
The Model WF-225 has capacity of 3.5 lbs./hr. and is designed for return duct applications.
A quiet heavy duty integral fan is used to overcome static resistance and discharges water mist through a
2 7/16 inch tube into the air duct. A heavy gauge mounting bracket secures the humidifier to the duct
The WF-225 is shipped with all necessary mounting hardware, water connectors, and instructions for installing. Complete WF-225 Specifications (466 KB). and Installation Sheets (340 KB). may be viewed or downloaded in a PDF format.
The Model WF-HP-226 produces up to 3 lbs./hr. of water mist and is designed for small sized
duct installations. A 2 in. diameter air intake tube plus the integral fan overcomes any static air pressure
in the duct. Water mist particles from the centrifugal atomizer unit are forced by the fan through a 2 7/16
in. tube, into the duct and carried with the air flow where the particles are completely
absorbed in a short distance.
Installation of the WF-HP-226 is greatly simplified by the mounting bracket and all necessary hardware and accessories. Installation can be in either horizontal or vertical ducts. Complete Specifications (484 KB). and Installation Sheets (405 KB). may be viewed or downloaded in a PDF format.
The Model WJ-228 can provide up to 12 lbs./hr. of water mist. The atomizing section rests in a water reservoir mounted in the bottom
of a horizontal duct. Air passes over and around the atomizer with little resistance.
The moisture will emistate into the duct air lowering the air temperature due to latent heat of emistation. The amount duct cooling and distance for mist absorption will depend upon inlet air humidity and temperature.
Typical applications include offices, laboratories and production spaces which are served by air quantities of more than 1200 cfm and where relative humidity as high as 50% is required. Specifications (259 KB). Installation Sheets (465 KB).
The Model WF-HH-229 has a capacity of 2 lbs./hr. and is especially designed to mount through a wall
for small room applications. As in all Humidity Source centrifugal atomizing humidifiers, a built in fan
discharges mist through a 2 7/16 in. tube which extends through the wall and into the room.
A mounting plate holds the humidifier and makes wall installation a simple task, all mounting hardware is included. Specifications (443 KB). and Installation Sheets (413 KB). may be viewed or downloaded in a PDF format.
Models WT and WT-B can provide up to 24 pounds of water mist per hour. The atomizing section rests in a small water reservoir
suspended under or mounted in the bottom of a horizontal duct run and air passes over and
around the atomizer producing negligible static pressure.
The moisture will emistate into the duct air and its latent heat of mistization will depress the dry bulb temperature of the duct air. The amount will depend upon the moisture and air quantities.
Typical applications include offices and laboratories or small production spaces which are served by air quantities of more than 2000 c.f.m. Specifications (212 KB). Installation Sheets (468 KB).
Humidity Source, LLC
Ph. 973-916-1001 Fax 973-916-0770